Oldcastle-buildingenvelope Reliance-HTC Manuale Utente

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY!Phone: 1-

AW-375 @ 1 3/4" glazingAW-385 @ 2" glazing(top & bottom of mullion)AW-370 @ 1 3/4" glazingAW-380 @ 2" glazing(top & bottom

1.6 Drill 5/16˜ diameter weep holes at 1/4 points in the horizontal pressure plate. Drill (1) 5/16˜ diameter weep holeat the bottom of each horizon

Anchor type and sizes vary per job requirements. Details shown in these instructions are to be used asa guide only. Refer to approved shop drawings fo

FIGURE 6Last Bay Horizontal NotchSINGLE & TWIN SPAN INSTALLATION (cont’d): 2.1.3 Install verticals plumb and level, ensuring proper spacing

2 1/2"3/4"Apply bond breakertape along face of spliceInsert backer rodinto tongue of upper& lower mullionsSeal joint betweenmulls. Seal

2.3 Wipe excess sealant from exposed areas. Tool sealant into the joint between the horizontal and verticalat the glazing pocket. Avoid a buildup

Force sealantinto gasket raceSeal along tongue ofhorizontal & across face andtongue of mullion beforeinstalling zone plugs.STEP 1STEP 2Tool sealan

Seal along tongue of horizontal and acrossface of mullion before installing SSG bridge.STEP 1STEP 2SSG BRIDGE AT SILL(HEAD SIMILAR)Optionalinterior se

3.1 Install face gaskets into all pressure plates. Install silicone spacer gaskets into the SSG mullions. Crowdall gaskets into members to avoid g

3.3 Note: To avoid silicone curing before glass is set in place and contamination from job−site debris,glazing prep must be done as each opening is

TABLE OF CONTENTSGeneral Information Product Use

3.5 Set glass in opening. Ensure that glass bite is equal on all sides. CAUTION: Be certain that glass isplaced firmly against interior gasket to

3.7 If required, install GP−111 (1˜, 1 3/4" & 2" infill) or GP−112 (1/4˜ infill) side blocks with silicone at centerlineof each lite o

2 1/2"SSG verticalQuarter pointsQuarter points1/4" splice joint1/2"face coversplice joint118"Face cover(dashed)FS−325Butt−splice i

3.10 After removing vertical temporary retainers, install vertical pressure plates with FS−325 screws at 9" O.C.3.11 After removing horizontal te

WW−162 cut length =D.L.O. minus 1/4"5/16"Ø weep holeslocated at 1/4 pointsWW−110 face cover.Weep horizontal coverat mid−lite. See detail bel

A.1 Notch vertical adaptors at captured mullions according to FIGURE 19. Horizontal adaptors are straightcut. Install vertical adaptors first, le

Captured Glazing Adaptor for SSG Mullion#10 x 3" PFH;Attach to mullion perapproved shop drawings;Stagger from pressureplate screw locationsStanda

1/2"face coversplice1/2"1"1/2"pressureplate splice3" first screw location atupper pressure plate2"Glazing adaptorPressur

Step 2Step 3Step 1Seal betweenpressure plates1/2"1/2"Pressure plate splice1/2" above face cover spliceInstall face covers leaving1/2&qu

All door framing components are shipped fabricated from the factory. The main curtain wall framingcan be erected prior to installing the doors.C.1 C

R E L I A N C E − H T C I N S T A L L A T I O N M A N U A LTABLE OF CONTENTSSection 3: Glazing

FIGURE 25Sealing Verticals at Entrance DoorsAD-450thermal door frameSeal void at bottom of subframe,sloping sealant down to marrywith threshold sealTu

Anchoring Door Jamb with SideliteAttach mullionto channel withflat head screws(see approvedshop drawings)Anchoring Door Jamb without SideliteDoor jamb

E.1 Reglazing must be done from the exterior. carefully remove face covers surrounding the lite of glass to bedeglazed. SEE FIGURE 27.E.2 Remove

FIGURE 28 shows the basic layout of the standard one−piece corner mullion assembly. These details are forgeneral reference and do not necessarily ref

AW−500Vertical & JambHead & SillHorizontal7 1/4" SYSTEM, 1 3/4" GLAZINGSSG MullionAW−501AW−504AW−505AW−800Vertical & JambHead &a

CORNER MULLIONS & ACCESSORIESFace Cover90° OS Captured1 3/4" InfillAW−115AW−117Pressure Plate90° OS Captured1 3/4" InfillGlazing Adaptor

CORNER MULLIONS & ACCESSORIESAW−121Setting Chair1 3/4" InfillAW−131AW−123Setting Chair2" InfillAW−122Pocket Filler1 3/4" Infill(use

Splice SleeveUse with AW−504AW−195−01Splice SleeveUse with AW−800 &AW−850AW−196−01PARTS LIST#10 x 1" Phillips Pan HeadHorizontal to Shear Blo

WW−103−14Jamb "F" AnchorUse with AW−500 &AW−550WW−103−13WW−103−12WW−103−11WW−102−21WW−102−20Intermediate "T" AnchorUse with AW

STANDARD ACCESSORIESWW−373Captured Mullion Zone Plug2" InfillWW−382SSG Mullion Bridge1 3/4" InfillWW−383SSG Mullion Bridge2" InfillPART

GENERAL INFORMATIONPRODUCT USEThe Reliance Triple Glaze curtain wall system is intended for installation by glazing professionals withappropriate exp

GENERAL INFORMATIONPROTECTION AND STORAGEHandle all material carefully. Do not drop from the truck. Stack with adequate separation so the material w

GENERAL INFORMATIONEXPANSION JOINTSExpansion joints and perimeter joints shown in these instructions and in the shop drawings are shown at nominalsize

INSTALLATION TYPESMullion end anchorMullion mid−point anchor(deadload)Mullion mid−point anchor(expansion)Mullion spliceMullion end anchorMullion end a

FRAME FABRICATIONUnless otherwise noted, the details shown in these instructions reflect the 7 1/4˜ systemfor 1 3/4˜ glazing. 7 1/2" system for

FRAME FABRICATIONtyp.Quarter pointsD.L.O. minus 1/16"Roll−Over Head/SillD.L.O.Tubular HorizontalMidpoint5/16" dia. weep hole(bottom leg of f